[Info-vax] PCSI install fails

[CY]

$ product
_Operation (INSTALL, SHOW, ...): show
_(PROD, HIST, OBJ, RECOV, UTIL): prod
_Product name (* to show list): *
------------------------------------ ----------- ---------
PRODUCT                              KIT TYPE    STATE
------------------------------------ ----------- ---------
HP I64VMS AVAIL_MAN_BASE V8.3-1H1    Full LP     Installed
HP I64VMS CDSA V2.3-306              Full LP     Installed
HP I64VMS DECNET_PHASE_IV V8.3-1H1   Full LP     Installed
HP I64VMS DWMOTIF V1.6               Full LP     Installed
HP I64VMS DWMOTIF_SUPPORT V8.3-1H1   Full LP     Installed
HP I64VMS KERBEROS V3.1-152          Full LP     Installed
HP I64VMS OPENVMS V8.3-1H1           Platform    Installed
HP I64VMS SSL V1.3-284               Full LP     Installed
HP I64VMS TCPIP V5.6-9ECO2           Full LP     Installed
HP I64VMS TDC_RT V2.3-1              Full LP     Installed
HP I64VMS VMS V8.3-1H1               Oper System Installed
HP I64VMS WBEMCIM V2.61-A070728      Full LP     Installed
HP I64VMS WBEMPROVIDERS V1.5-31      Full LP     Installed
------------------------------------ ----------- ---------
13 items found
$ prod
_Operation (INSTALL, SHOW, ...): inst
_Product name (* to show list): *

   1 - HP I64VMS VMS83I_PCSI V2.0          Patch (remedial update)
   2 - HP I64VMS VMS83I_UPDATE V8.0        Patch (remedial update)
   3 - All products listed above
   ? - Help
   E - Exit

Choose one or more items from the menu: 1

Performing product kit validation of signed kits ...
%PCSI-I-VALPASSED, validation of $1$DGA100:<000000.UPGRADE_KITS>HP-
I64VMS-VMS83I_PCSI-V0200--4.PCSI$COMPRESSED;1 succeeded

%PCSI-E-APPLYTOERR, maintenance product HP I64VMS VMS83I_PCSI V2.0
applies to a product that is not installed
-PCSI-E-APPLYTOPRD, prerequisite product is HP I64VMS VMS V8.3
%PCSI-E-S_OPFAIL, operation failed
%PCSIUI-E-ABORT, operation terminated due to an unrecoverable error
condition
$

This kit is needed for the upgrade as HP states:

KIT NAME:

     VMS83I_UPDATE-V0800


2  KIT DESCRIPTION:

     2.1  Installation Rating:

     INSTALL_1 :  To be installed by all customers.

     This installation rating, based upon current CLD information, is
     provided to serve as a guide to which customers should apply this
     remedial kit.  (Reference attached Disclaimer of Warranty and
     Limitation of Liability Statement)


     2.2  Reboot Requirement:

     Reboot Required.

     HP strongly recommends that a reboot is performed immediately
after
     kit installation to avoid system instability.  If you have other
     nodes in your OpenVMS cluster, they must also be rebooted in
order
     to make use of the new image(s).  If it is not possible or
     convenient to reboot the entire cluster at this time, a rolling
     re-boot may be performed.

     In addition to the reboot, some kits that have been included in
the
     VMS83I_UPDATE-V0800 kit have specific steps that must be
performed
     before or after the installation of the VMS83I_UPDATE-V0800 patch
     kit.  Refer to section 7.5 "Special Installation Instructions"
for
     any such requirements BEFORE attempting to install the
     VMS83I_UPDATE-V0800 patch kit.


     2.3  Version(s) of OpenVMS to which this kit may be applied:

     OpenVMS Integrity V8.3


     2.4  New functionality or new hardware support provided:

     Yes.  See the following files for more information:

      o  [SYSHLP]VMS83I_ACMELDAP-V0200.RELEASE_NOTES

      o  [SYSHLP]VMS83I_IPB-V0200.RELEASE_NOTES


                                                                Page 2


3  KITS SUPERSEDED BY THIS KIT:


      -  VMS83I_UPDATE-V0700



4  KIT DEPENDENCIES:

     4.1  The following remedial kit(s), or later, must be installed
          BEFORE installation of this, or any required kit:


      -  VMS83I_PCSI-V0200



     4.2  In order to receive all the corrections listed in this kit,
          the following remedial kits, or later, should also be
          installed:


      -  None


What am I doing wrong?????
//CY