[Info-vax] MSA$UTIL will list SAS disk serial numbers on new Smart Array controllers such as the Pxxx series of controllers.
brian
bdcorbin at gmail.com
Thu May 24 13:37:52 EDT 2012
brian wrote:
> Is there a way to collect a SCSI/SAS disk serial number remotely in VMS
> from DCL?
>
> I've tested the OpenVMS ALpha V8.4 command line utilities below and they
> do not report the device serial number from the Vital Product data frame.
>
> -SCSI_INFO
> -cddvd$tools.cld ( tested on CDDROM and Hard disk. )
> %CDDVD-S-NOSERNUM, No device serial number data is available
> -SAS$UTIL
> -MSA$UTIL
>
> A friend has showed me an output from his OpenVMS System management Home
> page that can show the serial number for a direct attached SCSI disk (
> not connected to smart array) , I believe it uses
> SNMP to collect the data.
>
>
> regards Brian
An update on MSA$UTIL and SAS$UTIL command show disk/full
My previous tests of MSA$UTIL was on Parallel SCSI Smart Array adapters
such as the 5300 and 6400 series controllers, and these do not show the
disk serial numbers. I recently had access to an rx2800 i2 servers with
the integrated P410I Smart Array controller and the SHOW DISK/FULL
command from MSA$UTIL will list the SAS disk serial number.
Further testing on Standard SAS controllers using the SAS$UTIL command
Show Disk/full does not list the Serial Number.
Here is an example of MSA$util from an rx2800 I2 with OpenVMS 8.4
mcr msa$util
MSA>
MSA>
MSA> set controller pka0
MSA> show controller
Adapter: _PKA0: (DEFAULT)
P410i (c) HP 50014380132B5980
Software 5.06
Port Address: 50014380-132b5980
Supported Redundancy Mode: Not Available.
Cache:
0 megabyte read/write cache
Cache is disabled and Cache is not configured.
No unflushed data in cache.
Battery:
Battery is not reported as present.
MSA>
MSA> show disk/full
SAS device [Disk]
Disk 1: bus: 1, Target id: 0, Port: 1I, Box/Enclosure: 0, Bay: 1,
size 279.40
[300.00]GB
Disk 1, # 0, size 585858420 blocks, (279.36 [299.96] GB), Unit 0.
Disk 1, # 1, size 13544 blocks, (6.61 [6.93] MB), Unused.
Connector Location Internal
Connector 1I.
Enclosure 0.
Bay 1
WWID 0x5000cca0211ae4a1
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVGTHEB
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
Drive is configured as part of a logical volume.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 2: bus: 1, Target id: 1, Port: 1I, Box/Enclosure: 0, Bay: 2,
size 279.40
[300.00]GB
Disk 2, # 0, size 585858420 blocks, (279.36 [299.96] GB), Unit 0.
Disk 2, # 1, size 13544 blocks, (6.61 [6.93] MB), Unused.
Connector Location Internal
Connector 1I.
Enclosure 0.
Bay 2
WWID 0x5000cca0211b4561
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVGZY5B
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
Drive is configured as part of a logical volume.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 3: bus: 1, Target id: 2, Port: 1I, Box/Enclosure: 0, Bay: 3,
size 279.40
[300.00]GB
Disk 3, Spare for unit 0
Connector Location Internal
Connector 1I.
Enclosure 0.
Bay 3
WWID 0x5000cca02116b291
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVDGZ0B
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
Drive is configured as part of a logical volume.
Drive is configured to be a spare.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 4: bus: 1, Target id: 3, Port: 1I, Box/Enclosure: 0, Bay: 4,
size 279.40
[300.00]GB
Disk 4, # 0, size 585858420 blocks, (279.36 [299.96] GB), Unit 1.
Disk 4, # 1, size 13544 blocks, (6.61 [6.93] MB), Unused.
Connector Location Internal
Connector 1I.
Enclosure 0.
Bay 4
WWID 0x5000cca021181bb1
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVE80KB
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
Drive is configured as part of a logical volume.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 5: bus: 1, Target id: 4, Port: 2I, Box/Enclosure: 1, Bay: 5,
size 279.40
[300.00]GB
Disk 5, # 0, size 585871964 blocks, (279.37 [299.97] GB), Unused.
Connector Location Internal
Connector 2I.
Enclosure 1.
Bay 5
WWID 0x5000cca02116f7fd
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVDMLAB
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 6: bus: 1, Target id: 5, Port: 2I, Box/Enclosure: 1, Bay: 6,
size 279.40
[300.00]GB
Disk 6, # 0, size 585858420 blocks, (279.36 [299.96] GB), Unit 1.
Disk 6, # 1, size 13544 blocks, (6.61 [6.93] MB), Unused.
Connector Location Internal
Connector 2I.
Enclosure 1.
Bay 6
WWID 0x5000cca0211b6a45
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVH2DAB
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
Drive is configured as part of a logical volume.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 7: bus: 1, Target id: 6, Port: 2I, Box/Enclosure: 1, Bay: 7,
size 279.40
[300.00]GB
Disk 7, Spare for unit 1
Connector Location Internal
Connector 2I.
Enclosure 1.
Bay 7
WWID 0x5000cca0211ae17d
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVGT8YB
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason None.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
Drive is configured as part of a logical volume.
Drive is configured to be a spare.
write cache is changeable and drive has a "safe" write cache.
SAS device [Disk]
Disk 8: bus: 1, Target id: 7, Port: 2I, Box/Enclosure: 1, Bay: 8,
size 279.40
[300.00]GB
Disk 8, # 0, size 585871964 blocks, (279.37 [299.97] GB), Unused.
Connector Location Internal
Connector 2I.
Enclosure 1.
Bay 8
WWID 0x5000cca021194589
Device Type Disk
Device Vendor ID HP
Device Product ID EG0300FBDBR
Device Serial Number PMVEWVGB
Device Firmware Version HPD6
Reserved blocks 65536. (32.000000 MB)
Block Size(bytes/sector) 512.
RPM 10020.
Compaq Drive Stamp(M&P Data Stamp) Yes
Last Failure Reason Init reset recovery aborted.
Physical Disk Flags:
S.M.A.R.T. predictive failure supported
Yes.
S.M.A.R.T. predictive failures recorded in the factory M&P data
No.
S.M.A.R.T. predictive failure is enabled
Yes.
S.M.A.R.T. predictive failures recorded in the since power M&P data
No.
Drive attached to external connector
No.
write cache is changeable and drive has a "safe" write cache.
MSA>
Here is an example of SAS$UTIL on a BL870C blade
$ mcr sas$util
SAS> set controller pka0
Selected controller _PKA0: is a LSISAS10xx device.
SAS> sho disk
Port _PKA0:
---- --- --- --- -------- ------- -------- ------------------
-----------------
ID Enc PHY Slt Device Type Size(MB) SAS Address Product
Name
---- --- --- --- -------- ------- -------- ------------------
-----------------
03 DA 02 03 DKA300 SAS 70007 5000C500-0F39DFC5 HP
DG072.. HPDC
04 DA 03 04 DKA400 SAS 70007 5000C500-0F39BE2D HP
DG072.. HPDC
01 - - - DKA1 RAID 1 69617 E49D2A86-059215C0 LSIL
Logic.. HP01L
SAS> sho disk/full
SAS ID: 3
Product Name : HP DG072BB975 HPDC3
SAS WWID : 5000C500-0F39DFC5
Phy Num : 2
Target ID : 3
Physical Slot : 3
Device Info SSP Target Direct Attached
Device Flags Device is present in SAS topology.
Device is mapped to a Bus and Target ID.
Device Bus and Target ID mapping is not persistent.
Size : 70007 MB / 143374738 blocks
SAS ID: 4
Product Name : HP DG072BB975 HPDC3
SAS WWID : 5000C500-0F39BE2D
Phy Num : 3
Target ID : 4
Physical Slot : 4
Device Info SSP Target Direct Attached
Device Flags Device is present in SAS topology.
Device is mapped to a Bus and Target ID.
Device Bus and Target ID mapping is not persistent.
Size : 70007 MB / 143374738 blocks
IR Volume ID: 1
Product Name : LSILOGIC Logical Volume HP01L
Size : 69617 MB / 142577663 blocks
Volume Type : RAID 1 (LSI Logic Integrated Mirror)
SAS Address : 059215C0-E49D2A86
More information about the Info-vax
mailing list