[Info-vax] Error using fibre channel target on FreeBSD from OpenVMS
Volker Halle
volker_halle at hotmail.com
Thu Apr 28 01:22:17 EDT 2022
Matthew,
the value 132 is the system service status code:
VSIAXP $ exit 132
%SYSTEM-F-DEVOFFLINE, device is not in configuration or not available
Here is the SCSI_INFO data from an emulated DGA device on a CHARON-AXP emulator:
VSIAXP $ scsi_info $1$dga0
$!
$! SCSI_INFO V3
$!
$! Copyright (c) 1995 by DIGITAL Equipment Corporation, Maynard, Mass.
$! All Rights Reserved. Unpublished rights reserved under the copyright
$! laws of the United States.
$!
$! Issuing INQUIRY QIOW
$!
$! SCSI Inquiry Data (255 bytes) :
$!
$! 000: 00 00 02 02 1F 00 00 53 56 69 72 74 75 61 6C 20
$! 010: 48 53 56 33 30 30 20 20 20 20 20 20 20 20 20 20
$! 020: 30 32 30 30 00 00 00 00 00 00 00 00 00 00 00 00
$! 030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 0A0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 0B0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 0C0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 0D0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 0E0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 0F0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Peripheral Device Type : Direct Access
$!
$! Peripheral Device Qualifier :
$!
$! Peripheral device type supported & connected to target
$!
$! Vendor Identification : Virtual
$!
$! Product Identification: HSV300
$!
$! Product Revision Level: 0200
$!
$! ANSI Information:
$!
$! Complies to SCSI-2
$!
$! ISO Information:
$!
$! 0 - does not claim ISO SCSI (ISO IS 9316) compliance
$!
$! ECMA Information:
$!
$! 0 - does not claim ECMA SCSI (ECMA-111) compliance
$!
$! Removable Media: No
$!
$! AEN Capability: No
$!
$! Command Queuing: Yes
$!
$! 16-Bit Wide Bus Data Transfers: No
$!
$! 32-Bit Wide Bus Data Transfers: Yes
$!
$! Linked Commands: No
$!
$! Soft Reset Alternative: Yes
$!
$! Relative Addressing: No
$!
$! Synchronous Data Transfers: Yes
$!
$! Issuing Test Unit Ready command
$!
$! ========================== Read-Write Error Recovery Page ==================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 01h
$!
$! SCSI 6-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 17 00 00 08 00 00 00 00 00 00 02 00 01 0A 00 00
$! 010: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 23
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 01h
$! Page Name ................. Read-Write Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 01h
$!
$! SCSI 6-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 17 00 00 08 00 00 00 00 00 00 02 00 01 0A FF FF
$! 010: FF FF FF 00 FF 00 FF FF
$!
$! Mode Sense Data Length ...... 23
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 01h
$! Page Name ................. Read-Write Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. FF FF FF FF FF 00 FF 00
$! FF FF
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 01h
$!
$! SCSI 10-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 00 1A 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 01 0A 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 26
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 01h
$! Page Name ................. Read-Write Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 01h
$!
$! SCSI 10-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 00 1A 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 01 0A FF FF FF FF FF 00 FF 00 FF FF
$!
$! Mode Sense Data Length ...... 26
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 01h
$! Page Name ................. Read-Write Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. FF FF FF FF FF 00 FF 00
$! FF FF
$!
$! ============================ Disconnect-Reconnect Page =====================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 02h
$!
$! SCSI 6-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 1B 00 00 08 00 00 00 00 00 00 02 00 02 0E 00 00
$! 010: 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 27
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 02h
$! Page Name ................. Disconnect-Reconnect
$! Saveable .................. No
$! Size ...................... 14
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 02h
$!
$! SCSI 6-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 1B 00 00 08 00 00 00 00 00 00 02 00 02 0E 00 00
$! 010: 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 27
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 02h
$! Page Name ................. Disconnect-Reconnect
$! Saveable .................. No
$! Size ...................... 14
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 02h
$!
$! SCSI 10-Byte Mode Sense command returned 32 bytes of data:
$!
$! 000: 00 1E 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 02 0E 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 30
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 02h
$! Page Name ................. Disconnect-Reconnect
$! Saveable .................. No
$! Size ...................... 14
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 02h
$!
$! SCSI 10-Byte Mode Sense command returned 32 bytes of data:
$!
$! 000: 00 1E 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 02 0E 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 30
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 02h
$! Page Name ................. Disconnect-Reconnect
$! Saveable .................. No
$! Size ...................... 14
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00
$!
$! ================================ Format Device Page ========================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 03h
$!
$! SCSI 6-Byte Mode Sense command returned 36 bytes of data:
$!
$! 000: 23 00 00 08 00 00 00 00 00 00 02 00 03 16 00 00
$! 010: 00 00 00 00 00 00 00 3F 02 00 00 00 00 00 00 00
$! 020: 00 00 00 00
$!
$! Mode Sense Data Length ...... 35
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 03h
$! Page Name ................. Format Device
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 3F 02 00 00 00 00 00 00 00 00 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 03h
$!
$! SCSI 6-Byte Mode Sense command returned 36 bytes of data:
$!
$! 000: 23 00 00 08 00 00 00 00 00 00 02 00 03 16 00 00
$! 010: 00 00 00 00 00 00 00 3F 02 00 00 00 00 00 00 00
$! 020: 00 00 00 00
$!
$! Mode Sense Data Length ...... 35
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 03h
$! Page Name ................. Format Device
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 3F 02 00 00 00 00 00 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 03h
$!
$! SCSI 10-Byte Mode Sense command returned 40 bytes of data:
$!
$! 000: 00 26 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 03 16 00 00 00 00 00 00 00 00 00 3F 02 00 00 00
$! 020: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 38
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 03h
$! Page Name ................. Format Device
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 3F 02 00 00 00 00 00 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 03h
$!
$! SCSI 10-Byte Mode Sense command returned 40 bytes of data:
$!
$! 000: 00 26 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 03 16 00 00 00 00 00 00 00 00 00 3F 02 00 00 00
$! 020: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 38
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 03h
$! Page Name ................. Format Device
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 3F 02 00 00 00 00 00 00 00 00 00 00 00
$!
$! ============================= Rigid Disk Geometry Page =====================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 04h
$!
$! SCSI 6-Byte Mode Sense command returned 36 bytes of data:
$!
$! 000: 23 00 00 08 00 00 00 00 00 00 02 00 04 16 00 00
$! 010: 1A 3F 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 15 18 00 00
$!
$! Mode Sense Data Length ...... 35
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 04h
$! Page Name ................. Rigid Disk Geometry
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 1A 3F 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 15 18 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 04h
$!
$! SCSI 6-Byte Mode Sense command returned 36 bytes of data:
$!
$! 000: 23 00 00 08 00 00 00 00 00 00 02 00 04 16 00 00
$! 010: 1A 3F 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00
$!
$! Mode Sense Data Length ...... 35
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 04h
$! Page Name ................. Rigid Disk Geometry
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 1A 3F 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 04h
$!
$! SCSI 10-Byte Mode Sense command returned 40 bytes of data:
$!
$! 000: 00 26 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 04 16 00 00 1A 3F 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 15 18 00 00
$!
$! Mode Sense Data Length ...... 38
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 04h
$! Page Name ................. Rigid Disk Geometry
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 1A 3F 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 15 18 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 04h
$!
$! SCSI 10-Byte Mode Sense command returned 40 bytes of data:
$!
$! 000: 00 26 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 04 16 00 00 1A 3F 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 38
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 04h
$! Page Name ................. Rigid Disk Geometry
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 1A 3F 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! ================================ Flexible Disk Page ========================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 05h
$!
$! SCSI 6-Byte Mode Sense command returned 44 bytes of data:
$!
$! 000: 2B 00 00 08 00 00 00 00 00 00 02 00 05 1E 00 FA
$! 010: 02 0F 02 00 00 50 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 43
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 05h
$! Page Name ................. Flexible Disk
$! Saveable .................. No
$! Size ...................... 30
$! Hex Data .................. 00 FA 02 0F 02 00 00 50
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
$! 00 00 00 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 05h
$!
$! SCSI 6-Byte Mode Sense command returned 44 bytes of data:
$!
$! 000: 2B 00 00 08 00 00 00 00 00 00 02 00 05 1E 00 00
$! 010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 43
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 05h
$! Page Name ................. Flexible Disk
$! Saveable .................. No
$! Size ...................... 30
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
$! 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 05h
$!
$! SCSI 10-Byte Mode Sense command returned 48 bytes of data:
$!
$! 000: 00 2E 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 05 1E 00 FA 02 0F 02 00 00 50 00 00 00 00 00 00
$! 020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 46
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 05h
$! Page Name ................. Flexible Disk
$! Saveable .................. No
$! Size ...................... 30
$! Hex Data .................. 00 FA 02 0F 02 00 00 50
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
$! 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 05h
$!
$! SCSI 10-Byte Mode Sense command returned 48 bytes of data:
$!
$! 000: 00 2E 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 05 1E 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 46
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 05h
$! Page Name ................. Flexible Disk
$! Saveable .................. No
$! Size ...................... 30
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00
$! 00 00 00 00 00 00
$!
$! ============================ Verify Error Recovery Page ====================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 07h
$!
$! SCSI 6-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 17 00 00 08 00 00 00 00 00 00 02 00 07 0A 00 00
$! 010: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 23
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 07h
$! Page Name ................. Verify Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 07h
$!
$! SCSI 6-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 17 00 00 08 00 00 00 00 00 00 02 00 07 0A 0F FF
$! 010: FF 00 00 00 00 00 FF FF
$!
$! Mode Sense Data Length ...... 23
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 07h
$! Page Name ................. Verify Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 0F FF FF 00 00 00 00 00
$! FF FF
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 07h
$!
$! SCSI 10-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 00 1A 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 07 0A 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 26
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 07h
$! Page Name ................. Verify Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 07h
$!
$! SCSI 10-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 00 1A 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 07 0A 0F FF FF 00 00 00 00 00 FF FF
$!
$! Mode Sense Data Length ...... 26
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 07h
$! Page Name ................. Verify Error Recovery
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 0F FF FF 00 00 00 00 00
$! FF FF
$!
$! =================================== Caching Page ===========================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 08h
$!
$! SCSI 6-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 17 00 00 08 00 00 00 00 00 00 02 00 08 0A 00 00
$! 010: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 23
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 08h
$! Page Name ................. Caching
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 08h
$!
$! SCSI 6-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 17 00 00 08 00 00 00 00 00 00 02 00 08 0A 07 FF
$! 010: FF FF FF FF FF FF FF FF
$!
$! Mode Sense Data Length ...... 23
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 08h
$! Page Name ................. Caching
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 07 FF FF FF FF FF FF FF
$! FF FF
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 08h
$!
$! SCSI 10-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 00 1A 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 08 0A 00 00 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 26
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 08h
$! Page Name ................. Caching
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 08h
$!
$! SCSI 10-Byte Mode Sense command returned 28 bytes of data:
$!
$! 000: 00 1A 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 08 0A 07 FF FF FF FF FF FF FF FF FF
$!
$! Mode Sense Data Length ...... 26
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 08h
$! Page Name ................. Caching
$! Saveable .................. No
$! Size ...................... 10
$! Hex Data .................. 07 FF FF FF FF FF FF FF
$! FF FF
$!
$! ============================== Peripheral Device Page ======================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 09h
$!
$! SCSI 6-Byte Mode Sense command returned 20 bytes of data:
$!
$! 000: 13 00 00 08 00 00 00 00 00 00 02 00 09 06 00 00
$! 010: 00 00 00 00
$!
$! Mode Sense Data Length ...... 19
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 09h
$! Page Name ................. Peripheral Device
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 09h
$!
$! SCSI 6-Byte Mode Sense command returned 20 bytes of data:
$!
$! 000: 13 00 00 08 00 00 00 00 00 00 02 00 09 06 00 00
$! 010: 00 00 00 00
$!
$! Mode Sense Data Length ...... 19
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 09h
$! Page Name ................. Peripheral Device
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 09h
$!
$! SCSI 10-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 00 16 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 09 06 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 22
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 09h
$! Page Name ................. Peripheral Device
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 09h
$!
$! SCSI 10-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 00 16 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 09 06 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 22
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 09h
$! Page Name ................. Peripheral Device
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! ================================ Control Mode Page =========================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 0Ah
$!
$! SCSI 6-Byte Mode Sense command returned 20 bytes of data:
$!
$! 000: 13 00 00 08 00 00 00 00 00 00 02 00 0A 06 00 00
$! 010: 00 00 00 00
$!
$! Mode Sense Data Length ...... 19
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ah
$! Page Name ................. Control Mode
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 0Ah
$!
$! SCSI 6-Byte Mode Sense command returned 20 bytes of data:
$!
$! 000: 13 00 00 08 00 00 00 00 00 00 02 00 0A 06 00 00
$! 010: 00 00 00 00
$!
$! Mode Sense Data Length ...... 19
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ah
$! Page Name ................. Control Mode
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 0Ah
$!
$! SCSI 10-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 00 16 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 0A 06 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 22
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ah
$! Page Name ................. Control Mode
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 0Ah
$!
$! SCSI 10-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 00 16 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 0A 06 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 22
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ah
$! Page Name ................. Control Mode
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! =========================== Medium Types Supported Page ====================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 0Bh
$!
$! SCSI 6-Byte Mode Sense command returned 20 bytes of data:
$!
$! 000: 13 00 00 08 00 00 00 00 00 00 02 00 0B 06 00 00
$! 010: 00 00 00 00
$!
$! Mode Sense Data Length ...... 19
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Bh
$! Page Name ................. Medium Types Supported
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 0Bh
$!
$! SCSI 6-Byte Mode Sense command returned 20 bytes of data:
$!
$! 000: 13 00 00 08 00 00 00 00 00 00 02 00 0B 06 00 00
$! 010: 00 00 00 00
$!
$! Mode Sense Data Length ...... 19
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Bh
$! Page Name ................. Medium Types Supported
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 0Bh
$!
$! SCSI 10-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 00 16 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 0B 06 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 22
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Bh
$! Page Name ................. Medium Types Supported
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 0Bh
$!
$! SCSI 10-Byte Mode Sense command returned 24 bytes of data:
$!
$! 000: 00 16 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 0B 06 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 22
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Bh
$! Page Name ................. Medium Types Supported
$! Saveable .................. No
$! Size ...................... 6
$! Hex Data .................. 00 00 00 00 00 00
$!
$! ============================= Notch and Partition Page =====================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 0Ch
$!
$! SCSI 6-Byte Mode Sense command returned 36 bytes of data:
$!
$! 000: 23 00 00 08 00 00 00 00 00 00 02 00 0C 16 00 00
$! 010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 20 00 00 00
$!
$! Mode Sense Data Length ...... 35
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ch
$! Page Name ................. Notch and Partition
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 20 00 00 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 0Ch
$!
$! SCSI 6-Byte Mode Sense command returned 36 bytes of data:
$!
$! 000: 23 00 00 08 00 00 00 00 00 00 02 00 0C 16 00 00
$! 010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00
$!
$! Mode Sense Data Length ...... 35
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ch
$! Page Name ................. Notch and Partition
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 0Ch
$!
$! SCSI 10-Byte Mode Sense command returned 40 bytes of data:
$!
$! 000: 00 26 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 0C 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 20 00 00 00
$!
$! Mode Sense Data Length ...... 38
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ch
$! Page Name ................. Notch and Partition
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 20 00 00 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 0Ch
$!
$! SCSI 10-Byte Mode Sense command returned 40 bytes of data:
$!
$! 000: 00 26 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$! 010: 0C 16 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$! 020: 00 00 00 00 00 00 00 00
$!
$! Mode Sense Data Length ...... 38
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Page Code ................. 0Ch
$! Page Name ................. Notch and Partition
$! Saveable .................. No
$! Size ...................... 22
$! Hex Data .................. 00 00 00 00 00 00 00 00
$! 00 00 00 00 00 00 00 00 00 00 00 00 00 00
$!
$! =============================== Vendor Specific Page =======================
$!
$! Issuing 6-byte MODE SENSE QIOW to get current values for page 00h
$!
$! SCSI 6-Byte Mode Sense command returned 12 bytes of data:
$!
$! 000: 0B 00 00 08 00 00 00 00 00 00 02 00
$!
$! Mode Sense Data Length ...... 11
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Issuing 6-byte MODE SENSE QIOW to get changeable values for page 00h
$!
$! SCSI 6-Byte Mode Sense command returned 12 bytes of data:
$!
$! 000: 0B 00 00 08 00 00 00 00 00 00 02 00
$!
$! Mode Sense Data Length ...... 11
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get current values for page 00h
$!
$! SCSI 10-Byte Mode Sense command returned 16 bytes of data:
$!
$! 000: 00 0E 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$!
$! Mode Sense Data Length ...... 14
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$! Issuing 10-byte MODE SENSE QIOW to get changeable values for page 00h
$!
$! SCSI 10-Byte Mode Sense command returned 16 bytes of data:
$!
$! 000: 00 0E 00 00 00 00 00 08 00 00 00 00 00 00 02 00
$!
$! Mode Sense Data Length ...... 14
$! Medium Type ................. 00h
$! Device-Specific Parameter ... 00h
$! Block Descriptor Length ..... 8
$! Block Descriptor Data ....... 00 00 00 00 00 00 02 00
$!
$!
More information about the Info-vax
mailing list