[Info-vax] ECO 831H1 UPDATE V7.0

[Scott]

On Dec 15, 7:48 am, pe... at langstoeger.at (Peter 'EPLAN' LANGSTOeGER)
wrote:
> In article <a02c4ab0-bbe6-4d41-a28a-7b9460184... at k13g2000prh.googlegroups.com>, Scott <sta... at saic.com> writes:
>
> >I've logged a call with ITRC as well.
>
> Any response so far?
>
> >Just prior to the execution phase of the new UPDATE V7.0 ECO, this
> >message is seen:
>
> >* This product does not have any configuration options.
>
> >    << WBEMCIM Kit to be Installed >>
>
> >    In order to complete the installation of VMS831H1I_UPDATE you also
> >need to install:
>
> >    HPI64VMSWBEMCIMV2.91-A090219
>
> >    Do you want to continue? [YES] YES
>
> Yes, the same message is seen when you install the VMS831H1I_ICAP ECO.
> (which is included in the UPDATE and therefor the message is seen, too)
> I simply ignored it...
>
> >Q: We haven't configured iCAP for use on this Integrity system and
> >don't plan to use it.
>
> So do I.
>
> >                       I'm wondering if this Update V7.0 patch is
> >complete?
>
> I don't know for sure, but I'm relaxed and trust this UPDATE ECO (but if I'm
> wrong, nobody is harmed here, it is only me ;-)
>
> >           Also, did not see any release of WBEMCIM V2.91 product.
>
> Well, the readme suggests, that there is a V2.9
>
>        http://openvms.compaq.com/doc/83final/wbem/readme.txt
>
>   HP WBEM Services for OpenVMS, V2.9 (WBEMCIM) is shipped with OpenVMS
>   Version 8.3-1H1.
>
>   Installing or upgrading WBEM Services involves two steps:
>
>   o Running the OpenVMS Product Install utility to install/upgrade the
>   WBEMCIM kit.
>   ($product install wbemcim)
>
>   o Running the WBEM Services configuration utility after the installation.
>   ($run sys$sysroot:[wbem_services]wbem_services$config.exe)
>
>   Documentation on how to configure WBEM Services is included in the
>   OpenVMS installation manual:
>   "HP OpenVVMS Version 8.3-1H1 for Integrity Servers Upgrade and
>   Installation Manual", section 7.8.5 "Configure WBEM Services for OpenVMS".
>
> but on the OpenVMS I64 V8.3-1H1 DVD one can find:
>
> Directory LDA1:[WBEMCIM_I64.KIT]
>
> HP-I64VMS-WBEMCIM-V0261-A070728-1.PCSI$COMPRESSED;1
>                    ****  21-AUG-2007 09:21:26.40  [SYSTEM]         (RWD,RWD,,RE)
> HP-I64VMS-WBEMCIM-V0261-A070728-1.PCSI$COMPRESSED_ESW;1
>                      18  21-AUG-2007 09:22:02.07  [SYSTEM]         (RWD,RWD,,RE)
>
> Total of 2 files, 175490 blocks.
>
> so,http://openvms.compaq.com/doc/wbem.htmlseems to be the only hint to V2.9
>
> --
> Peter "EPLAN" LANGSTÖGER
> Network and OpenVMS system specialist
> E-mail  Pe... at LANGSTOeGER.at
> A-1030 VIENNA  AUSTRIA              I'm not a pessimist, I'm a realist

This was the update that I put in the ITRC call...

"I received a call from David/HP and he said that we are likely
fine since we do not have iCAP configured. The UPDATE V7.0 patch
does install the iCAP image files...however, we are not using any
of this."